Daddy of all Z's
Moderator:Accord98
- docaam
- UB Advanced Member
- Posts:1169
- Joined:06 Jul 2009, 1:42 pm
- Vehicle:G35s and 370Z
- Location:Route 66
Got the wheels Work Meister CR01 with Gun Metal center
15 X 8.5 -9 around 95mm lip
15 x 9.5 -24mm around 135mm lip biggest you can get
Placing against the car :tup:
have to think where what should go
15 X 8.5 -9 around 95mm lip
15 x 9.5 -24mm around 135mm lip biggest you can get
Placing against the car :tup:
have to think where what should go
- docaam
- UB Advanced Member
- Posts:1169
- Joined:06 Jul 2009, 1:42 pm
- Vehicle:G35s and 370Z
- Location:Route 66
Kind of one phase is done. I will move the car for exhaust on Saturday and from there to paint shop. They will start the car today before taking it for exhaust.
Engine, gearbox with new clutch, differential, rear axle, radiator, fans all installed.
Custom engine mounts
Radiator was fro 1JZ but will run custom pipe
Flex A lite twin fans, shroud is for Mitsubishi eclipse but got a good deal on it.
Drivetrian would be fitted today
Fuel cell mounted and fitted
Engine, gearbox with new clutch, differential, rear axle, radiator, fans all installed.
Custom engine mounts
Radiator was fro 1JZ but will run custom pipe
Flex A lite twin fans, shroud is for Mitsubishi eclipse but got a good deal on it.
Drivetrian would be fitted today
Fuel cell mounted and fitted
- leroythtsme
- UB Addicted Member
- Posts:168
- Joined:20 Jul 2010, 2:00 am
- Vehicle:Nissan Altima 2010 2.5s
first the 370... now this.
BRILLIANT
BRILLIANT
- docaam
- UB Advanced Member
- Posts:1169
- Joined:06 Jul 2009, 1:42 pm
- Vehicle:G35s and 370Z
- Location:Route 66
Car was supposed to be painted yesterday but it was a day off so hopefully today
Some pictures I took Thursday night, after painting door jams all panels were in final alignment phase.
Door jams and inside of doors painted
Rear bumper aligned, will get bumpers and front grill powder coated once they will close all the holes
Rest of body
Front air damper and bumper installed
Trying the fender flares
Front caster is too much out
Rear not sure this
or this
Some pictures I took Thursday night, after painting door jams all panels were in final alignment phase.
Door jams and inside of doors painted
Rear bumper aligned, will get bumpers and front grill powder coated once they will close all the holes
Rest of body
Front air damper and bumper installed
Trying the fender flares
Front caster is too much out
Rear not sure this
or this
- kartoos100
- UB Senior Member
- Posts:788
- Joined:16 Sep 2006, 4:50 pm
- Vehicle:08 IS300 + 05 Civic
- Location:Sharjah, UAE
Maaan! That is starting to look good!
- docaam
- UB Advanced Member
- Posts:1169
- Joined:06 Jul 2009, 1:42 pm
- Vehicle:G35s and 370Z
- Location:Route 66
I got some parts for the Z will post details they time they are ready for installation. As of now car has been sanded and polished and fitting of the parts has started. Took it on a recovery for a quick wash inside out.
Engine looks clean now
Even clearcoated underside of the hood
Finish seems to be great
I got cusco front and rear struts and motorsports sway bars along with some exciting stuff from Techno Toy Tuning they make some excellent suspension parts for older Toyota and Datusn/Nissans. I always felt the lack of camber and caster setting and a weaker stock suspension so got myself these from them, only down point is their parts are a bit heavy but im not that much bothered about weight saving.
Rear lower control arms, will allows to adjust toe and camber, and can also move the tire within fender wall about 1/2"and can widen the rear track by 1"
Front lower control arms, again widen and shortening along with camber and toe setting, have two setting for sway bars and in total very touch compared to stock ones, come with new ball joints as well.
Tension control rods, got these to adjust the caster as thats a priority, even after cutting the fenders wheels is touching on turning
got new bixenon headlights, will fit in place of old halogen stock ones, good thing is they are also made of glass as OEM ones.
side by side
car wont be complete without CF, for the start got the rear tail light panel and BRE replica spoiler CF wrapped at Carbonsignal, result as always amazing
Engine looks clean now
Even clearcoated underside of the hood
Finish seems to be great
I got cusco front and rear struts and motorsports sway bars along with some exciting stuff from Techno Toy Tuning they make some excellent suspension parts for older Toyota and Datusn/Nissans. I always felt the lack of camber and caster setting and a weaker stock suspension so got myself these from them, only down point is their parts are a bit heavy but im not that much bothered about weight saving.
Rear lower control arms, will allows to adjust toe and camber, and can also move the tire within fender wall about 1/2"and can widen the rear track by 1"
Front lower control arms, again widen and shortening along with camber and toe setting, have two setting for sway bars and in total very touch compared to stock ones, come with new ball joints as well.
Tension control rods, got these to adjust the caster as thats a priority, even after cutting the fenders wheels is touching on turning
got new bixenon headlights, will fit in place of old halogen stock ones, good thing is they are also made of glass as OEM ones.
side by side
car wont be complete without CF, for the start got the rear tail light panel and BRE replica spoiler CF wrapped at Carbonsignal, result as always amazing
- UAE NEWBIE
- UB Dedicated Member
- Posts:273
- Joined:02 Jun 2011, 9:42 pm
looking real good. Paint looks great